! %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% ! Copyright (c) 2009, Roger Marchand, version 1.2 ! All rights reserved. ! Redistribution and use in source and binary forms, with or without modification, are ! permitted provided that the following conditions are met: ! 1. Redistributions of source code must retain the above copyright notice, this list of ! conditions and the following disclaimer. ! 2. Redistributions in binary form must reproduce the above copyright notice, this list ! of conditions and the following disclaimer in the documentation and/or other ! materials provided with the distribution. ! 3. Neither the name of the copyright holder nor the names of its contributors may be ! used to endorse or promote products derived from this software without specific prior ! written permission. ! THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY ! EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF ! MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL ! THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, ! SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT ! OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS ! INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT ! LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE ! OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. ! History ! May 2015 - D. Swales - Modified for COSPv2.0 ! %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% MODULE MOD_MISR_SIMULATOR use cosp_kinds, only: wp use MOD_COSP_STATS, ONLY: hist2D use mod_cosp_config, ONLY: R_UNDEF,numMISRHgtBins,numMISRTauBins,misr_histHgt, & misr_histTau implicit none ! Parameters real(wp),parameter :: & misr_taumin = 0.3_wp, & ! Minimum optical depth for joint-histogram tauchk = -1.*log(0.9999999) ! Lower limit on optical depth contains ! ###################################################################################### ! SUBROUTINE misr_subcolumn ! ###################################################################################### SUBROUTINE MISR_SUBCOLUMN(npoints,ncol,nlev,dtau,zfull,at,sunlit,tauOUT, & dist_model_layertops,box_MISR_ztop) ! INPUTS INTEGER, intent(in) :: & npoints, & ! Number of horizontal gridpoints ncol, & ! Number of subcolumns nlev ! Number of vertical layers INTEGER, intent(in),dimension(npoints) :: & sunlit ! 1 for day points, 0 for night time REAL(WP),intent(in),dimension(npoints,ncol,nlev) :: & dtau ! Optical thickness REAL(WP),intent(in),dimension(npoints,nlev) :: & zfull, & ! Height of full model levels (i.e. midpoints), [nlev] is bottom at ! Temperature (K) ! OUTPUTS REAL(WP),intent(out),dimension(npoints,ncol) :: & box_MISR_ztop, & ! Cloud-top height in each column tauOUT ! Optical depth in each column REAL(WP),intent(out),dimension(npoints,numMISRHgtBins) :: & dist_model_layertops ! ! INTERNAL VARIABLES INTEGER :: ilev,j,loop,ibox,thres_crossed_MISR INTEGER :: iMISR_ztop REAL(WP) :: cloud_dtau,MISR_penetration_height,ztest ! ############################################################################ ! Initialize box_MISR_ztop(1:npoints,1:ncol) = 0._wp do j=1,npoints ! Estimate distribution of Model layer tops dist_model_layertops(j,:)=0 do ilev=1,nlev ! Define location of "layer top" if(ilev.eq.1 .or. ilev.eq.nlev) then ztest=zfull(j,ilev) else ztest=0.5_wp*(zfull(j,ilev)+zfull(j,ilev-1)) endif ! Find MISR layer that contains this level ! *NOTE* the first MISR level is "no height" level iMISR_ztop=2 do loop=2,numMISRHgtBins if ( ztest .gt. 1000*misr_histHgt(loop+1) ) then iMISR_ztop=loop+1 endif enddo dist_model_layertops(j,iMISR_ztop) = dist_model_layertops(j,iMISR_ztop)+1 enddo ! For each GCM cell or horizontal model grid point do ibox=1,ncol ! Compute optical depth as a cummulative distribution in the vertical (nlev). tauOUT(j,ibox)=sum(dtau(j,ibox,1:nlev)) thres_crossed_MISR=0 do ilev=1,nlev ! If there a cloud, start the counter and store this height if(thres_crossed_MISR .eq. 0 .and. dtau(j,ibox,ilev) .gt. 0.) then ! First encountered a "cloud" thres_crossed_MISR = 1 cloud_dtau = 0 endif if( thres_crossed_MISR .lt. 99 .and. thres_crossed_MISR .gt. 0 ) then if( dtau(j,ibox,ilev) .eq. 0.) then ! We have come to the end of the current cloud layer without yet ! selecting a CTH boundary. Restart cloud tau counter cloud_dtau=0 else ! Add current optical depth to count for the current cloud layer cloud_dtau=cloud_dtau+dtau(j,ibox,ilev) endif ! If the cloud is continuous but optically thin (< 1) from above the ! current layer cloud top to the current level then MISR will like ! see a top below the top of the current layer. if( dtau(j,ibox,ilev).gt.0 .and. (cloud_dtau-dtau(j,ibox,ilev)) .lt. 1) then if(dtau(j,ibox,ilev) .lt. 1 .or. ilev.eq.1 .or. ilev.eq.nlev) then ! MISR will likely penetrate to some point within this layer ... the middle MISR_penetration_height=zfull(j,ilev) else ! Take the OD = 1.0 level into this layer MISR_penetration_height=0.5_wp*(zfull(j,ilev)+zfull(j,ilev-1)) - & 0.5_wp*(zfull(j,ilev-1)-zfull(j,ilev+1))/dtau(j,ibox,ilev) endif box_MISR_ztop(j,ibox)=MISR_penetration_height endif ! Check for a distinctive water layer if(dtau(j,ibox,ilev) .gt. 1 .and. at(j,ilev) .gt. 273 ) then ! Must be a water cloud, take this as CTH level thres_crossed_MISR=99 endif ! If the total column optical depth is "large" than MISR can't see ! anything else. Set current point as CTH level if(sum(dtau(j,ibox,1:ilev)) .gt. 5) then thres_crossed_MISR=99 endif endif enddo ! Check to see if there was a cloud for which we didn't ! set a MISR cloud top boundary if( thres_crossed_MISR .eq. 1) then ! If the cloud has a total optical depth of greater ! than ~ 0.5 MISR will still likely pick up this cloud ! with a height near the true cloud top ! otherwise there should be no CTH if(sum(dtau(j,ibox,1:nlev)) .gt. 0.5) then ! keep MISR detected CTH elseif(sum(dtau(j,ibox,1:nlev)) .gt. 0.2) then ! MISR may detect but wont likley have a good height box_MISR_ztop(j,ibox)=-1 else ! MISR not likely to even detect. ! so set as not cloudy box_MISR_ztop(j,ibox)=0 endif endif enddo ! loop of subcolumns enddo ! loop of gridpoints ! Modify MISR CTH for satellite spatial / pattern matcher effects ! Code in this region added by roj 5/2006 to account ! for spatial effect of the MISR pattern matcher. ! Basically, if a column is found between two neighbors ! at the same CTH, and that column has no hieght or ! a lower CTH, THEN misr will tend to but place the ! odd column at the same height as it neighbors. ! This setup assumes the columns represent a about a 1 to 4 km scale ! it will need to be modified significantly, otherwise ! ! DS2015: Add loop over gridpoints and index accordingly. ! if(ncol.eq.1) then ! ! Adjust based on neightboring points. ! do j=2,npoints-1 ! if(box_MISR_ztop(j-1,1) .gt. 0 .and. & ! box_MISR_ztop(j+1,1) .gt. 0 .and. & ! abs(box_MISR_ztop(j-1,1)-box_MISR_ztop(j+1,1)) .lt. 500 .and. & ! box_MISR_ztop(j,1) .lt. box_MISR_ztop(j+1,1)) then ! box_MISR_ztop(j,1) = box_MISR_ztop(j+1,1) ! endif ! enddo ! else ! ! Adjust based on neighboring subcolumns. ! do j=1,npoints ! do ibox=2,ncol-1 ! if(box_MISR_ztop(j,ibox-1) .gt. 0 .and. & ! box_MISR_ztop(j,ibox+1) .gt. 0 .and. & ! abs(box_MISR_ztop(j,ibox-1)-box_MISR_ztop(j,ibox+1)) .lt. 500 .and. & ! box_MISR_ztop(j,ibox) .lt. box_MISR_ztop(j,ibox+1)) then ! box_MISR_ztop(j,ibox) = box_MISR_ztop(j,ibox+1) ! endif ! enddo ! enddo ! endif ! ! DS2015 END ! Fill dark scenes do j=1,numMISRHgtBins where(sunlit .ne. 1) dist_model_layertops(1:npoints,j) = R_UNDEF enddo end SUBROUTINE MISR_SUBCOLUMN ! ###################################################################################### ! SUBROUTINE misr_column ! ###################################################################################### SUBROUTINE MISR_COLUMN(npoints,ncol,box_MISR_ztop,sunlit,tau,MISR_cldarea,MISR_mean_ztop,fq_MISR_TAU_v_CTH) ! INPUTS INTEGER, intent(in) :: & npoints, & ! Number of horizontal gridpoints ncol ! Number of subcolumns INTEGER, intent(in),dimension(npoints) :: & sunlit ! 1 for day points, 0 for night time REAL(WP),intent(in),dimension(npoints,ncol) :: & box_MISR_ztop, & ! Cloud-top height in each column tau ! Column optical thickness ! OUTPUTS REAL(WP),intent(inout),dimension(npoints) :: & MISR_cldarea, & ! Fraction area covered by clouds MISR_mean_ztop ! Mean cloud top height MISR would observe REAL(WP),intent(inout),dimension(npoints,7,numMISRHgtBins) :: & fq_MISR_TAU_v_CTH ! Joint histogram of cloud-cover and tau ! INTERNAL VARIABLES INTEGER :: j LOGICAL,dimension(ncol) :: box_cloudy real(wp),dimension(npoints,ncol) :: tauWRK,box_MISR_ztopWRK ! ############################################################################ ! Compute column quantities and joint-histogram MISR_cldarea(1:npoints) = 0._wp MISR_mean_ztop(1:npoints) = 0._wp fq_MISR_TAU_v_CTH(1:npoints,1:7,1:numMISRHgtBins) = 0._wp tauWRK(1:npoints,1:ncol) = tau(1:npoints,1:ncol) box_MISR_ztopWRK(1:npoints,1:ncol) = box_MISR_ztop(1:npoints,1:ncol) do j=1,npoints ! Subcolumns that are cloudy(true) and not(false) box_cloudy(1:ncol) = merge(.true.,.false.,tau(j,1:ncol) .gt. tauchk) ! Fill optically thin clouds with fill value where(.not. box_cloudy(1:ncol)) tauWRK(j,1:ncol) = -999._wp where(box_MISR_ztopWRK(j,1:ncol) .eq. 0) box_MISR_ztopWRK(j,1:ncol)=-999._wp ! Compute joint histogram and column quantities for points that are sunlit and cloudy if (sunlit(j) .eq. 1) then ! Joint histogram call hist2D(tauWRK(j,1:ncol),box_MISR_ztopWRK(j,1:ncol),ncol,misr_histTau,numMISRTauBins,& 1000*misr_histHgt,numMISRHgtBins,fq_MISR_TAU_v_CTH(j,1:numMISRTauBins,1:numMISRHgtBins)) fq_MISR_TAU_v_CTH(j,1:numMISRTauBins,1:numMISRHgtBins) = & 100._wp*fq_MISR_TAU_v_CTH(j,1:numMISRTauBins,1:numMISRHgtBins)/ncol ! Column cloud area MISR_cldarea(j)=real(count(box_MISR_ztopWRK(j,1:ncol) .ne. -999.))/ncol ! Column cloud-top height if ( count(box_MISR_ztopWRK(j,1:ncol) .ne. -999.) .ne. 0 ) then MISR_mean_ztop(j) = sum(box_MISR_ztopWRK(j,1:ncol),box_MISR_ztopWRK(j,1:ncol) .ne. -999.)/ & count(box_MISR_ztopWRK(j,1:ncol) .ne. -999.) else MISR_mean_ztop(j) = R_UNDEF endif else MISR_cldarea(j) = R_UNDEF MISR_mean_ztop(npoints) = R_UNDEF endif enddo end SUBROUTINE MISR_COLUMN end MODULE MOD_MISR_SIMULATOR