[3880] | 1 | ! radiation_gas.F90 - Derived type to store the gas mixing ratios |
---|
| 2 | ! |
---|
| 3 | ! (C) Copyright 2014- ECMWF. |
---|
| 4 | ! |
---|
| 5 | ! This software is licensed under the terms of the Apache Licence Version 2.0 |
---|
| 6 | ! which can be obtained at http://www.apache.org/licenses/LICENSE-2.0. |
---|
| 7 | ! |
---|
| 8 | ! In applying this licence, ECMWF does not waive the privileges and immunities |
---|
| 9 | ! granted to it by virtue of its status as an intergovernmental organisation |
---|
| 10 | ! nor does it submit to any jurisdiction. |
---|
| 11 | ! |
---|
| 12 | ! Author: Robin Hogan |
---|
| 13 | ! Email: r.j.hogan@ecmwf.int |
---|
| 14 | ! |
---|
| 15 | ! Modifications |
---|
| 16 | ! 2019-01-14 R. Hogan Added out_of_physical_bounds routine |
---|
| 17 | |
---|
| 18 | module radiation_gas |
---|
| 19 | |
---|
| 20 | use parkind1, only : jprb |
---|
| 21 | |
---|
| 22 | implicit none |
---|
| 23 | public |
---|
| 24 | |
---|
| 25 | ! Gas codes; these indices match those of RRTM-LW up to 7 |
---|
| 26 | integer, parameter :: IGasNotPresent = 0 |
---|
| 27 | integer, parameter :: IH2O = 1 |
---|
| 28 | integer, parameter :: ICO2 = 2 |
---|
| 29 | integer, parameter :: IO3 = 3 |
---|
| 30 | integer, parameter :: IN2O = 4 |
---|
| 31 | integer, parameter :: ICO = 5 |
---|
| 32 | integer, parameter :: ICH4 = 6 |
---|
| 33 | integer, parameter :: IO2 = 7 |
---|
| 34 | integer, parameter :: ICFC11 = 8 |
---|
| 35 | integer, parameter :: ICFC12 = 9 |
---|
| 36 | integer, parameter :: IHCFC22= 10 |
---|
| 37 | integer, parameter :: ICCl4 = 11 |
---|
| 38 | integer, parameter :: INO2 = 12 |
---|
| 39 | integer, parameter :: NMaxGases = 12 |
---|
| 40 | |
---|
| 41 | ! Molar masses (g mol-1) of dry air and the various gases above |
---|
| 42 | real(jprb), parameter :: IAirMolarMass = 28.970 |
---|
| 43 | real(jprb), parameter, dimension(0:NMaxGases) :: IGasMolarMass = (/ & |
---|
| 44 | & 0.0_jprb, & ! Gas not present |
---|
| 45 | & 18.0152833_jprb, & ! H2O |
---|
| 46 | & 44.011_jprb, & ! CO2 |
---|
| 47 | & 47.9982_jprb, & ! O3 |
---|
| 48 | & 44.013_jprb, & ! N2O |
---|
| 49 | & 28.0101_jprb, & ! CO |
---|
| 50 | & 16.043_jprb, & ! CH4 |
---|
| 51 | & 31.9988_jprb, & ! O2 |
---|
| 52 | & 137.3686_jprb, & ! CFC11 |
---|
| 53 | & 120.914_jprb, & ! CFC12 |
---|
| 54 | & 86.469_jprb, & ! HCFC22 |
---|
| 55 | & 153.823_jprb, & ! CCl4 |
---|
| 56 | & 46.0055_jprb /) ! NO2 |
---|
| 57 | |
---|
| 58 | ! The corresponding names of the gases in upper and lower case, used |
---|
| 59 | ! for reading variables from the input file |
---|
| 60 | character*6, dimension(NMaxGases), parameter :: GasName & |
---|
| 61 | & = (/'H2O ','CO2 ','O3 ','N2O ','CO ','CH4 ', & |
---|
| 62 | & 'O2 ','CFC11 ','CFC12 ','HCFC22','CCl4 ','NO2 '/) |
---|
| 63 | character*6, dimension(NMaxGases), parameter :: GasLowerCaseName & |
---|
| 64 | & = (/'h2o ','co2 ','o3 ','n2o ','co ','ch4 ', & |
---|
| 65 | & 'o2 ','cfc11 ','cfc12 ','hcfc22','ccl4 ','no2 '/) |
---|
| 66 | |
---|
| 67 | ! Available units |
---|
| 68 | enum, bind(c) |
---|
| 69 | enumerator IMassMixingRatio, IVolumeMixingRatio |
---|
| 70 | end enum |
---|
| 71 | |
---|
| 72 | !--------------------------------------------------------------------- |
---|
| 73 | ! This derived type describes the gaseous composition of the |
---|
| 74 | ! atmosphere; gases may be stored as part of a 3D array (if their |
---|
| 75 | ! variation with height/column is to be represented) or one 1D array |
---|
| 76 | ! (if they are to be assumed globally well-mixed). |
---|
| 77 | type gas_type |
---|
| 78 | ! Units of each stored gas (or 0 if not present) |
---|
| 79 | integer :: iunits(NMaxGases) = 0 |
---|
| 80 | |
---|
| 81 | ! Scaling factor that should be applied to each stored gas to get |
---|
| 82 | ! a dimensionless result, e.g. if iunits=IVolumeMixingRatio then |
---|
| 83 | ! 1.0e-6 is used to indicate the units are actually PPMV: need to |
---|
| 84 | ! multiply by 1e-6 to get mol/mol. |
---|
| 85 | real(jprb) :: scale_factor(NMaxGases) = 1.0_jprb |
---|
| 86 | |
---|
| 87 | ! Mixing ratios of variable gases, dimensioned (ncol, nlev, |
---|
| 88 | ! NMaxGases) |
---|
| 89 | real(jprb), allocatable, dimension(:,:,:) :: mixing_ratio |
---|
| 90 | |
---|
| 91 | ! Flag to indicate whether a gas is present |
---|
| 92 | logical :: is_present(NMaxGases) = .false. |
---|
| 93 | |
---|
| 94 | ! Flag to indicate whether a gas is well mixed |
---|
| 95 | logical :: is_well_mixed(NMaxGases) = .false. |
---|
| 96 | |
---|
| 97 | integer :: ntype = 0 ! Number of gas types described |
---|
| 98 | |
---|
| 99 | integer :: ncol = 0 ! Number of columns in mixing_ratio |
---|
| 100 | integer :: nlev = 0 ! Number of levels in mixing_ratio |
---|
| 101 | |
---|
| 102 | ! A list of length ntype of gases whose volume mixing ratios have |
---|
| 103 | ! been provided |
---|
| 104 | integer :: icode(NMaxGases) = 0 |
---|
| 105 | |
---|
| 106 | contains |
---|
| 107 | procedure :: allocate => allocate_gas |
---|
| 108 | procedure :: deallocate => deallocate_gas |
---|
| 109 | procedure :: put => put_gas |
---|
| 110 | procedure :: put_well_mixed => put_well_mixed_gas |
---|
| 111 | procedure :: scale => scale_gas |
---|
| 112 | procedure :: set_units => set_units_gas |
---|
| 113 | procedure :: assert_units => assert_units_gas |
---|
| 114 | procedure :: get => get_gas |
---|
| 115 | procedure :: reverse => reverse_gas |
---|
| 116 | procedure :: out_of_physical_bounds |
---|
| 117 | end type gas_type |
---|
| 118 | |
---|
| 119 | contains |
---|
| 120 | |
---|
| 121 | |
---|
| 122 | !--------------------------------------------------------------------- |
---|
| 123 | subroutine allocate_gas(this, ncol, nlev) |
---|
| 124 | |
---|
| 125 | use yomhook, only : lhook, dr_hook |
---|
| 126 | |
---|
| 127 | class(gas_type), intent(inout) :: this |
---|
| 128 | integer, intent(in) :: ncol, nlev |
---|
| 129 | |
---|
| 130 | real(jprb) :: hook_handle |
---|
| 131 | |
---|
| 132 | if (lhook) call dr_hook('radiation_gas:allocate',0,hook_handle) |
---|
| 133 | |
---|
| 134 | call this%deallocate() |
---|
| 135 | |
---|
| 136 | allocate(this%mixing_ratio(ncol, nlev, NMaxGases)) |
---|
| 137 | this%mixing_ratio = 0.0_jprb |
---|
| 138 | |
---|
| 139 | this%ncol = ncol |
---|
| 140 | this%nlev = nlev |
---|
| 141 | |
---|
| 142 | if (lhook) call dr_hook('radiation_gas:allocate',1,hook_handle) |
---|
| 143 | |
---|
| 144 | end subroutine allocate_gas |
---|
| 145 | |
---|
| 146 | |
---|
| 147 | !--------------------------------------------------------------------- |
---|
| 148 | ! Deallocate memory and reset arrays |
---|
| 149 | subroutine deallocate_gas(this) |
---|
| 150 | |
---|
| 151 | use yomhook, only : lhook, dr_hook |
---|
| 152 | |
---|
| 153 | class(gas_type), intent(inout) :: this |
---|
| 154 | |
---|
| 155 | real(jprb) :: hook_handle |
---|
| 156 | |
---|
| 157 | if (lhook) call dr_hook('radiation_gas:deallocate',0,hook_handle) |
---|
| 158 | |
---|
| 159 | if (allocated(this%mixing_ratio)) then |
---|
| 160 | deallocate(this%mixing_ratio) |
---|
| 161 | end if |
---|
| 162 | |
---|
| 163 | this%iunits = 0 |
---|
| 164 | this%scale_factor = 0.0_jprb |
---|
| 165 | this%is_present = .false. |
---|
| 166 | this%is_well_mixed = .false. |
---|
| 167 | this%ntype = 0 |
---|
| 168 | this%ncol = 0 |
---|
| 169 | this%nlev = 0 |
---|
| 170 | this%icode = 0 |
---|
| 171 | |
---|
| 172 | if (lhook) call dr_hook('radiation_gas:deallocate',1,hook_handle) |
---|
| 173 | |
---|
| 174 | end subroutine deallocate_gas |
---|
| 175 | |
---|
| 176 | |
---|
| 177 | !--------------------------------------------------------------------- |
---|
| 178 | ! Put gas mixing ratio corresponding to gas ID "igas" with units |
---|
| 179 | ! "iunits" |
---|
| 180 | subroutine put_gas(this, igas, iunits, mixing_ratio, scale_factor, & |
---|
| 181 | istartcol) |
---|
| 182 | |
---|
| 183 | use yomhook, only : lhook, dr_hook |
---|
| 184 | use radiation_io, only : nulerr, radiation_abort |
---|
| 185 | |
---|
| 186 | class(gas_type), intent(inout) :: this |
---|
| 187 | integer, intent(in) :: igas |
---|
| 188 | integer, intent(in) :: iunits |
---|
| 189 | real(jprb), intent(in) :: mixing_ratio(:,:) |
---|
| 190 | real(jprb), optional, intent(in) :: scale_factor |
---|
| 191 | integer, optional, intent(in) :: istartcol |
---|
| 192 | |
---|
| 193 | integer :: i1, i2 |
---|
| 194 | |
---|
| 195 | real(jprb) :: hook_handle |
---|
| 196 | |
---|
| 197 | if (lhook) call dr_hook('radiation_gas:put',0,hook_handle) |
---|
| 198 | |
---|
| 199 | ! Check inputs |
---|
| 200 | if (igas <= IGasNotPresent .or. iunits > NMaxGases) then |
---|
| 201 | write(nulerr,'(a,i0,a,i0,a,i0)') '*** Error: provided gas ID (', & |
---|
| 202 | & igas, ') must be in the range ', IGasNotPresent+1, ' to ', & |
---|
| 203 | & NMaxGases |
---|
| 204 | call radiation_abort() |
---|
| 205 | end if |
---|
| 206 | if (iunits < IMassMixingRatio .or. iunits > IVolumeMixingRatio) then |
---|
| 207 | write(nulerr,'(a,i0,a,i0,a,i0)') '*** Error: provided gas units (', & |
---|
| 208 | & iunits, ') must be in the range ', IMassMixingRatio, ' to ', & |
---|
| 209 | & IVolumeMixingRatio |
---|
| 210 | call radiation_abort() |
---|
| 211 | end if |
---|
| 212 | |
---|
| 213 | if (.not. allocated(this%mixing_ratio)) then |
---|
| 214 | write(nulerr,'(a,i0,a,i0,a,i0)') '*** Error: attempt to put data to unallocated radiation_gas object' |
---|
| 215 | call radiation_abort() |
---|
| 216 | end if |
---|
| 217 | |
---|
| 218 | if (present(istartcol)) then |
---|
| 219 | i1 = istartcol |
---|
| 220 | else |
---|
| 221 | i1 = 1 |
---|
| 222 | end if |
---|
| 223 | |
---|
| 224 | i2 = i1 + size(mixing_ratio,1) - 1 |
---|
| 225 | |
---|
| 226 | if (i1 < 1 .or. i2 < 1 .or. i1 > this%ncol .or. i2 > this%ncol) then |
---|
| 227 | write(nulerr,'(a,i0,a,i0,a,i0)') '*** Error: attempt to put columns indexed ', & |
---|
| 228 | & i1, ' to ', i2, ' to array indexed 1 to ', this%ncol |
---|
| 229 | call radiation_abort() |
---|
| 230 | end if |
---|
| 231 | |
---|
| 232 | if (size(mixing_ratio,2) /= this%nlev) then |
---|
| 233 | write(nulerr,'(a,i0,a)') & |
---|
| 234 | & '*** Error: gas mixing ratio expected to have ', this%nlev, & |
---|
| 235 | & ' levels' |
---|
| 236 | call radiation_abort() |
---|
| 237 | end if |
---|
| 238 | |
---|
| 239 | if (.not. this%is_present(igas)) then |
---|
| 240 | ! Gas not present until now |
---|
| 241 | this%ntype = this%ntype + 1 |
---|
| 242 | this%icode(this%ntype) = igas |
---|
| 243 | end if |
---|
| 244 | this%is_present(igas) = .true. |
---|
| 245 | this%iunits(igas) = iunits |
---|
| 246 | this%is_well_mixed(igas) = .false. |
---|
| 247 | this%mixing_ratio(i1:i2,:,igas) = mixing_ratio |
---|
| 248 | |
---|
| 249 | if (present(scale_factor)) then |
---|
| 250 | this%scale_factor(igas) = scale_factor |
---|
| 251 | else |
---|
| 252 | this%scale_factor(igas) = 1.0_jprb |
---|
| 253 | end if |
---|
| 254 | |
---|
| 255 | if (lhook) call dr_hook('radiation_gas:put',1,hook_handle) |
---|
| 256 | |
---|
| 257 | end subroutine put_gas |
---|
| 258 | |
---|
| 259 | |
---|
| 260 | !--------------------------------------------------------------------- |
---|
| 261 | ! Put well-mixed gas mixing ratio corresponding to gas ID "igas" |
---|
| 262 | ! with units "iunits" |
---|
| 263 | subroutine put_well_mixed_gas(this, igas, iunits, mixing_ratio, & |
---|
| 264 | scale_factor, istartcol, iendcol) |
---|
| 265 | |
---|
| 266 | use yomhook, only : lhook, dr_hook |
---|
| 267 | use radiation_io, only : nulerr, radiation_abort |
---|
| 268 | |
---|
| 269 | class(gas_type), intent(inout) :: this |
---|
| 270 | integer, intent(in) :: igas |
---|
| 271 | integer, intent(in) :: iunits |
---|
| 272 | real(jprb), intent(in) :: mixing_ratio |
---|
| 273 | real(jprb), optional, intent(in) :: scale_factor |
---|
| 274 | integer, optional, intent(in) :: istartcol, iendcol |
---|
| 275 | |
---|
| 276 | real(jprb) :: hook_handle |
---|
| 277 | |
---|
| 278 | integer :: i1, i2 |
---|
| 279 | |
---|
| 280 | if (lhook) call dr_hook('radiation_gas:put_well_mixed',0,hook_handle) |
---|
| 281 | |
---|
| 282 | ! Check inputs |
---|
| 283 | if (igas <= IGasNotPresent .or. igas > NMaxGases) then |
---|
| 284 | write(nulerr,'(a,i0,a,i0,a,i0)') '*** Error: provided gas ID (', & |
---|
| 285 | & igas, ') must be in the range ', IGasNotPresent+1, ' to ', & |
---|
| 286 | & NMaxGases |
---|
| 287 | call radiation_abort() |
---|
| 288 | end if |
---|
| 289 | if (iunits < IMassMixingRatio .or. iunits > IVolumeMixingRatio) then |
---|
| 290 | write(nulerr,'(a,i0,a,i0,a,i0)') '*** Error: provided gas units (', & |
---|
| 291 | & iunits, ') must be in the range ', IMassMixingRatio, ' to ', & |
---|
| 292 | & IVolumeMixingRatio |
---|
| 293 | call radiation_abort() |
---|
| 294 | end if |
---|
| 295 | |
---|
| 296 | if (.not. allocated(this%mixing_ratio)) then |
---|
| 297 | write(nulerr,'(a)') '*** Error: attempt to put well-mixed gas data to unallocated radiation_gas object' |
---|
| 298 | call radiation_abort() |
---|
| 299 | end if |
---|
| 300 | |
---|
| 301 | if (present(istartcol)) then |
---|
| 302 | i1 = istartcol |
---|
| 303 | else |
---|
| 304 | i1 = 1 |
---|
| 305 | end if |
---|
| 306 | |
---|
| 307 | if (present(iendcol)) then |
---|
| 308 | i2 = iendcol |
---|
| 309 | else |
---|
| 310 | i2 = this%ncol |
---|
| 311 | end if |
---|
| 312 | |
---|
| 313 | if (i1 < 1 .or. i2 < 1 .or. i1 > this%ncol .or. i2 > this%ncol) then |
---|
| 314 | write(nulerr,'(a,i0,a,i0,a,i0)') '*** Error: attempt to put columns indexed ', & |
---|
| 315 | & i1, ' to ', i2, ' to array indexed 1 to ', this%ncol |
---|
| 316 | call radiation_abort() |
---|
| 317 | end if |
---|
| 318 | |
---|
| 319 | if (.not. this%is_present(igas)) then |
---|
| 320 | ! Gas not present until now |
---|
| 321 | this%ntype = this%ntype + 1 |
---|
| 322 | this%icode(this%ntype) = igas |
---|
| 323 | end if |
---|
| 324 | ! Map uses a negative value to indicate a well-mixed value |
---|
| 325 | this%is_present(igas) = .true. |
---|
| 326 | this%iunits(igas) = iunits |
---|
| 327 | this%is_well_mixed(igas) = .true. |
---|
| 328 | this%mixing_ratio(i1:i2,:,igas) = mixing_ratio |
---|
| 329 | |
---|
| 330 | if (present(scale_factor)) then |
---|
| 331 | this%scale_factor(igas) = scale_factor |
---|
| 332 | else |
---|
| 333 | this%scale_factor(igas) = 1.0_jprb |
---|
| 334 | end if |
---|
| 335 | |
---|
| 336 | if (lhook) call dr_hook('radiation_gas:put_well_mixed',1,hook_handle) |
---|
| 337 | |
---|
| 338 | end subroutine put_well_mixed_gas |
---|
| 339 | |
---|
| 340 | |
---|
| 341 | !--------------------------------------------------------------------- |
---|
| 342 | ! Scale gas concentrations, e.g. igas=ICO2 and set scale_factor=2 to |
---|
| 343 | ! double CO2. Note that this does not perform the scaling |
---|
| 344 | ! immediately, but changes the scale factor for the specified gas, |
---|
| 345 | ! ready to be used in set_units_gas. |
---|
| 346 | |
---|
| 347 | subroutine scale_gas(this, igas, scale_factor, lverbose) |
---|
| 348 | |
---|
| 349 | use radiation_io, only : nulout |
---|
| 350 | |
---|
| 351 | class(gas_type), intent(inout) :: this |
---|
| 352 | integer, intent(in) :: igas |
---|
| 353 | real(jprb), intent(in) :: scale_factor |
---|
| 354 | logical, optional, intent(in) :: lverbose |
---|
| 355 | |
---|
| 356 | if (scale_factor /= 1.0_jprb) then |
---|
| 357 | this%scale_factor(igas) = this%scale_factor(igas) * scale_factor |
---|
| 358 | if (present(lverbose)) then |
---|
| 359 | if (lverbose) then |
---|
| 360 | write(nulout,'(a,a,a,f0.3)') ' Scaling ', trim(GasName(igas)), & |
---|
| 361 | & ' concentration by ', scale_factor |
---|
| 362 | end if |
---|
| 363 | end if |
---|
| 364 | end if |
---|
| 365 | |
---|
| 366 | end subroutine scale_gas |
---|
| 367 | |
---|
| 368 | |
---|
| 369 | !--------------------------------------------------------------------- |
---|
| 370 | ! Scale the gas concentrations so that they have the units "iunits" |
---|
| 371 | ! and are therefore ready to be used by the gas optics model within |
---|
| 372 | ! ecRad with no further scaling. The existing scale_factor for each |
---|
| 373 | ! gas is applied. If "igas" is present then apply only to gas with |
---|
| 374 | ! ID "igas", otherwise to all gases. Optional argument scale_factor |
---|
| 375 | ! specifies scaling that any subsequent access would need to apply |
---|
| 376 | ! to get a dimensionless result (consistent with definition of |
---|
| 377 | ! gas_type). So say that your gas optics model requires gas |
---|
| 378 | ! concentrations in PPMV, specify iunits=IVolumeMixingRatio and |
---|
| 379 | ! scale_factor=1.0e-6. If the gas concentrations were currently |
---|
| 380 | ! dimensionless volume mixing ratios, then the values would be |
---|
| 381 | ! internally divided by 1.0e-6. |
---|
| 382 | recursive subroutine set_units_gas(this, iunits, igas, scale_factor) |
---|
| 383 | class(gas_type), intent(inout) :: this |
---|
| 384 | integer, intent(in) :: iunits |
---|
| 385 | integer, optional, intent(in) :: igas |
---|
| 386 | real(jprb), optional, intent(in) :: scale_factor |
---|
| 387 | |
---|
| 388 | integer :: ig |
---|
| 389 | |
---|
| 390 | ! Scaling factor to convert from old to new |
---|
| 391 | real(jprb) :: sf |
---|
| 392 | |
---|
| 393 | ! New scaling factor to store inside the gas object |
---|
| 394 | real(jprb) :: new_sf |
---|
| 395 | |
---|
| 396 | if (present(scale_factor)) then |
---|
| 397 | ! "sf" is the scaling to be applied now to the numbers (and may |
---|
| 398 | ! be modified below), "new_sf" is the value to be stored along |
---|
| 399 | ! with the numbers, informing subsequent routines how much you |
---|
| 400 | ! would need to multiply the numbers by to get a dimensionless |
---|
| 401 | ! result. |
---|
| 402 | sf = 1.0_jprb / scale_factor |
---|
| 403 | new_sf = scale_factor |
---|
| 404 | else |
---|
| 405 | sf = 1.0_jprb |
---|
| 406 | new_sf = 1.0_jprb |
---|
| 407 | end if |
---|
| 408 | |
---|
| 409 | if (present(igas)) then |
---|
| 410 | if (this%is_present(igas)) then |
---|
| 411 | if (iunits == IMassMixingRatio & |
---|
| 412 | & .and. this%iunits(igas) == IVolumeMixingRatio) then |
---|
| 413 | sf = sf * IGasMolarMass(igas) / IAirMolarMass |
---|
| 414 | else if (iunits == IVolumeMixingRatio & |
---|
| 415 | & .and. this%iunits(igas) == IMassMixingRatio) then |
---|
| 416 | sf = sf * IAirMolarMass / IGasMolarMass(igas) |
---|
| 417 | end if |
---|
| 418 | sf = sf * this%scale_factor(igas) |
---|
| 419 | |
---|
| 420 | if (sf /= 1.0_jprb) then |
---|
| 421 | this%mixing_ratio(:,:,igas) = this%mixing_ratio(:,:,igas) * sf |
---|
| 422 | end if |
---|
| 423 | ! Store the new units and scale factor for this gas inside the |
---|
| 424 | ! gas object |
---|
| 425 | this%iunits(igas) = iunits |
---|
| 426 | this%scale_factor(igas) = new_sf |
---|
| 427 | end if |
---|
| 428 | else |
---|
| 429 | do ig = 1,this%ntype |
---|
| 430 | call this%set_units(iunits, igas=this%icode(ig), scale_factor=new_sf) |
---|
| 431 | end do |
---|
| 432 | end if |
---|
| 433 | |
---|
| 434 | end subroutine set_units_gas |
---|
| 435 | |
---|
| 436 | |
---|
| 437 | !--------------------------------------------------------------------- |
---|
| 438 | ! Assert that gas mixing ratio units are "iunits", applying to gas |
---|
| 439 | ! with ID "igas" if present, otherwise to all gases. Otherwise the |
---|
| 440 | ! program will exit. Otional argument scale factor specifies any |
---|
| 441 | ! subsequent multiplication to apply; for PPMV one would use |
---|
| 442 | ! iunits=IVolumeMixingRatio and scale_factor=1.0e6. |
---|
| 443 | recursive subroutine assert_units_gas(this, iunits, igas, scale_factor) |
---|
| 444 | |
---|
| 445 | use radiation_io, only : nulerr, radiation_abort |
---|
| 446 | |
---|
| 447 | class(gas_type), intent(in) :: this |
---|
| 448 | integer, intent(in) :: iunits |
---|
| 449 | integer, optional, intent(in) :: igas |
---|
| 450 | real(jprb), optional, intent(in) :: scale_factor |
---|
| 451 | |
---|
| 452 | integer :: ig |
---|
| 453 | |
---|
| 454 | real(jprb) :: sf |
---|
| 455 | |
---|
| 456 | if (present(scale_factor)) then |
---|
| 457 | sf = scale_factor |
---|
| 458 | else |
---|
| 459 | sf = 1.0_jprb |
---|
| 460 | end if |
---|
| 461 | |
---|
| 462 | if (present(igas)) then |
---|
| 463 | if (this%is_present(igas)) then |
---|
| 464 | if (iunits /= this%iunits(igas)) then |
---|
| 465 | write(nulerr,'(a,a,a)') '*** Error: ', trim(GasName(igas)), & |
---|
| 466 | & ' is not in the required units' |
---|
| 467 | call radiation_abort() |
---|
| 468 | else if (sf /= this%scale_factor(igas)) then |
---|
| 469 | write(nulerr,'(a,a,a,e12.4,a,e12.4)') '*** Error: ', GasName(igas), & |
---|
| 470 | & ' scaling of ', this%scale_factor(igas), & |
---|
| 471 | & ' does not match required ', sf |
---|
| 472 | call radiation_abort() |
---|
| 473 | end if |
---|
| 474 | end if |
---|
| 475 | else |
---|
| 476 | do ig = 1,this%ntype |
---|
| 477 | call this%assert_units(iunits, igas=this%icode(ig), scale_factor=sf) |
---|
| 478 | end do |
---|
| 479 | end if |
---|
| 480 | |
---|
| 481 | end subroutine assert_units_gas |
---|
| 482 | |
---|
| 483 | |
---|
| 484 | !--------------------------------------------------------------------- |
---|
| 485 | ! Get gas mixing ratio corresponding to gas ID "igas" with units |
---|
| 486 | ! "iunits" and return as a 2D array of dimensions (ncol,nlev). The |
---|
| 487 | ! array will contain zeros if the gas is not stored. |
---|
| 488 | subroutine get_gas(this, igas, iunits, mixing_ratio, scale_factor, & |
---|
| 489 | & istartcol) |
---|
| 490 | |
---|
| 491 | use yomhook, only : lhook, dr_hook |
---|
| 492 | use radiation_io, only : nulerr, radiation_abort |
---|
| 493 | |
---|
| 494 | class(gas_type), intent(in) :: this |
---|
| 495 | integer, intent(in) :: igas |
---|
| 496 | integer, intent(in) :: iunits |
---|
| 497 | real(jprb), intent(out) :: mixing_ratio(:,:) |
---|
| 498 | real(jprb), optional, intent(in) :: scale_factor |
---|
| 499 | integer, optional, intent(in) :: istartcol |
---|
| 500 | |
---|
| 501 | real(jprb) :: sf |
---|
| 502 | integer :: i1, i2 |
---|
| 503 | |
---|
| 504 | real(jprb) :: hook_handle |
---|
| 505 | |
---|
| 506 | if (lhook) call dr_hook('radiation_gas:get',0,hook_handle) |
---|
| 507 | |
---|
| 508 | if (present(scale_factor)) then |
---|
| 509 | sf = scale_factor |
---|
| 510 | else |
---|
| 511 | sf = 1.0_jprb |
---|
| 512 | end if |
---|
| 513 | |
---|
| 514 | if (present(istartcol)) then |
---|
| 515 | i1 = istartcol |
---|
| 516 | else |
---|
| 517 | i1 = 1 |
---|
| 518 | end if |
---|
| 519 | |
---|
| 520 | i2 = i1 + size(mixing_ratio,1) - 1 |
---|
| 521 | |
---|
| 522 | if (i1 < 1 .or. i2 < 1 .or. i1 > this%ncol .or. i2 > this%ncol) then |
---|
| 523 | write(nulerr,'(a,i0,a,i0,a,i0)') '*** Error: attempt to get columns indexed ', & |
---|
| 524 | & i1, ' to ', i2, ' from array indexed 1 to ', this%ncol |
---|
| 525 | call radiation_abort() |
---|
| 526 | end if |
---|
| 527 | |
---|
| 528 | if (size(mixing_ratio,2) /= this%nlev) then |
---|
| 529 | write(nulerr,'(a,i0,a)') & |
---|
| 530 | & '*** Error: gas destination array expected to have ', this%nlev, & |
---|
| 531 | & ' levels' |
---|
| 532 | call radiation_abort() |
---|
| 533 | end if |
---|
| 534 | |
---|
| 535 | if (.not. this%is_present(igas)) then |
---|
| 536 | mixing_ratio = 0.0_jprb |
---|
| 537 | else |
---|
| 538 | if (iunits == IMassMixingRatio & |
---|
| 539 | & .and. this%iunits(igas) == IVolumeMixingRatio) then |
---|
| 540 | sf = sf * IGasMolarMass(igas) / IAirMolarMass |
---|
| 541 | else if (iunits == IVolumeMixingRatio & |
---|
| 542 | & .and. this%iunits(igas) == IMassMixingRatio) then |
---|
| 543 | sf = sf * IAirMolarMass / IGasMolarMass(igas) |
---|
| 544 | end if |
---|
| 545 | sf = sf * this%scale_factor(igas) |
---|
| 546 | |
---|
| 547 | if (sf /= 1.0_jprb) then |
---|
| 548 | mixing_ratio = this%mixing_ratio(i1:i2,:,igas) * sf |
---|
| 549 | else |
---|
| 550 | mixing_ratio = this%mixing_ratio(i1:i2,:,igas) |
---|
| 551 | end if |
---|
| 552 | end if |
---|
| 553 | |
---|
| 554 | if (lhook) call dr_hook('radiation_gas:get',1,hook_handle) |
---|
| 555 | |
---|
| 556 | end subroutine get_gas |
---|
| 557 | |
---|
| 558 | |
---|
| 559 | !--------------------------------------------------------------------- |
---|
| 560 | ! Copy data to "gas_rev", reversing the height ordering of the gas |
---|
| 561 | ! data |
---|
| 562 | subroutine reverse_gas(this, istartcol, iendcol, gas_rev) |
---|
| 563 | |
---|
| 564 | class(gas_type) :: this |
---|
| 565 | integer, intent(in) :: istartcol, iendcol |
---|
| 566 | type(gas_type), intent(out) :: gas_rev |
---|
| 567 | |
---|
| 568 | gas_rev%iunits = this%iunits |
---|
| 569 | gas_rev%scale_factor = this%scale_factor |
---|
| 570 | gas_rev%is_present = this%is_present |
---|
| 571 | gas_rev%is_well_mixed = this%is_well_mixed |
---|
| 572 | gas_rev%ntype = this%ntype |
---|
| 573 | gas_rev%ncol = this%ncol |
---|
| 574 | gas_rev%nlev = this%nlev |
---|
| 575 | gas_rev%icode = this%icode |
---|
| 576 | |
---|
| 577 | if (allocated(gas_rev%mixing_ratio)) deallocate(gas_rev%mixing_ratio) |
---|
| 578 | |
---|
| 579 | if (allocated(this%mixing_ratio)) then |
---|
| 580 | allocate(gas_rev%mixing_ratio(istartcol:iendcol,this%nlev,NMaxGases)) |
---|
| 581 | gas_rev%mixing_ratio(istartcol:iendcol,:,:) & |
---|
| 582 | & = this%mixing_ratio(istartcol:iendcol,this%nlev:1:-1,:) |
---|
| 583 | end if |
---|
| 584 | |
---|
| 585 | end subroutine reverse_gas |
---|
| 586 | |
---|
| 587 | !--------------------------------------------------------------------- |
---|
| 588 | ! Return .true. if variables are out of a physically sensible range, |
---|
| 589 | ! optionally only considering columns between istartcol and iendcol |
---|
| 590 | function out_of_physical_bounds(this, istartcol, iendcol, do_fix) result(is_bad) |
---|
| 591 | |
---|
| 592 | use yomhook, only : lhook, dr_hook |
---|
| 593 | use radiation_config, only : out_of_bounds_3d |
---|
| 594 | |
---|
| 595 | class(gas_type), intent(inout) :: this |
---|
| 596 | integer, optional,intent(in) :: istartcol, iendcol |
---|
| 597 | logical, optional,intent(in) :: do_fix |
---|
| 598 | logical :: is_bad |
---|
| 599 | |
---|
| 600 | logical :: do_fix_local |
---|
| 601 | |
---|
| 602 | real(jprb) :: hook_handle |
---|
| 603 | |
---|
| 604 | if (lhook) call dr_hook('radiation_gas:out_of_physical_bounds',0,hook_handle) |
---|
| 605 | |
---|
| 606 | if (present(do_fix)) then |
---|
| 607 | do_fix_local = do_fix |
---|
| 608 | else |
---|
| 609 | do_fix_local = .false. |
---|
| 610 | end if |
---|
| 611 | |
---|
| 612 | is_bad = out_of_bounds_3d(this%mixing_ratio, 'gas%mixing_ratio', & |
---|
| 613 | & 0.0_jprb, 1.0_jprb, do_fix_local, i1=istartcol, i2=iendcol) |
---|
| 614 | |
---|
| 615 | if (lhook) call dr_hook('radiation_gas:out_of_physical_bounds',1,hook_handle) |
---|
| 616 | |
---|
| 617 | end function out_of_physical_bounds |
---|
| 618 | |
---|
| 619 | end module radiation_gas |
---|